,

Evertz X-0401 X-Series 4×1 Video And Audio Router

Evertz
Availability:

In stock


Features

  • Supports SMPTE ST 424M (3GB/s), SMPTE ST 292-1 (1.5GB/s), SMPTE ST 259 (270, 360 or 540MB/s) and  DVB-ASI video signals
  • Switch point is fully controllable from the front panel
  • Video input presence detection displayable on the front panel
  • Front panel or remote control panel version available. Second control panel can be ordered for any version
  • Programmable source input names available on the front panel
  • Bypass verification test using main menu
  • Programmable tally output bus

 

The X-0401 supporting 3G/HD/SD SDI signals, a four input routing switcher provides a convenient, low cost way to route high definition and standard definition serial digital signals. The X-0401 routers are used for 3GB/s, 1.5GB/s, 270MB/s, 360MB/s, 540MB/s and DVB-ASI serial digital signals. When the unit is ordered with the Quad 4×1 AES router option the AES output busses can be used in an “audio follow video” mode, or can be broken away from the video bus. This router features the ability for redundancy protection with a bypass relay and optional dual power supplies.

The router electronics are housed in a 1RU rack mount frame and is controlled from the built-in front panel controls. Each model can also be purchased with an optional rack mount remote control panel that replaces the built-in control panel, or can be used as a second control panel. All units can also be controlled by Quartz over Ethernet, contact closures on the GPI control port or through the RS-232 or RS-422 serial remote control port using industry standard switcher protocols.

Embedded SoftSwitch™ Features (HES)
Routers equipped with EmbeddedSoftSwitch™ have all the features of the SoftSwitch™ versions as well as the following additional features. The embedded audio on the Video 1 buss uses Evertz patented SoftSwitch™ technology to eliminate audible pops when switches are performed (for SD, HD or 3G video). Embedded SoftSwitch™ is performed on all four audio groups.

SKU: X0401X Categories: , Tag:

Video Input

Standard

  • SMPTE ST 424-1 (3GB/s), SMPTE ST 292-1 (1.5GB/s), SMPTE ST 259 (270MB/s, 360MB/s, 540MB/s) and DVB-ASI

Number of Inputs

  • 4

Connector

  • BNC per IEC 61169-8 Annex A

Equalization

  • Automatic up to 165m@3G, 215m@HD, 275M@SD and with, bypass output 110m@3G, 175@HD, 200m@SD

Input Timing

  • +HES option only

Input Range

  • Measured with respect to the Genlock reference
  • ±1/2 line when Coarse phase = 1, Fine phase = 0

Video Output

Standard

  • Same as input

Number of Outputs

  • 2 per buss, 1 buss; Input 1 bypass protected

Connector

  • BNC per IEC 61169-8 Annex A

Signal Level

  • 800mV nominal

DC Offset

  • 0V ±0.5V

Output Timing

  • +HES option only

Output Phase

  • Measured with respect to the Genlock reference
  • Adjustable line buffer is used for clean and quiet switching

AES Audio Input AES4 Versions

Standard

  • SMPTE ST 276 single ended AES

Number of Inputs

  • 4 per bus, 4 busses

Connector

  • BNC per IEC 61169-8 Annex A

Signal Level

  • 1V p-p ±10%

AES Audio OutputAES4 Versions

Standard

  • SMPTE ST 276 single ended AES

Number of Outputs

  • 2 per buss, 4 busses; Input 1 bypass protected with +HBP option

Connector

  • BNC per IEC 61169-8 Annex A

Signal Level

  • 1V p-p

Reference

  • From Video Reference; On SoftSwitch™ model, menu selectable to Video or DARS

Video Reference

Type

  • Menu selectable; NTSC or PAL Colour Black 1V p-p
  • Composite Bi-level Sync (525i/59.94 or 625i/50) 300mV, HD Tri-level Sync

Number of Connectors

  • 2

Connector

  • BNC per IEC 61169-8 Annex A

Termination

  • High impedance loop through

GPI Control Port

Number of Inputs

  • 8 opto-isolated, programmable functions

Number of Outputs

  • 4 sets of relay contacts, normally closed, programmable functions

Relay Max Current

  • 1A at 30V DC

Remote Control Panel Port

Standard

  • RS-422, 9600 baud rate

Connector

  • 6 pins on GPUIO 25 pin female “D”

Protocol

Remote Control Panel

Serial Remote Control

Standard

  • RS-232 or RS-422

Connector

  • 9 pin female “D”

Protocol

  • GVG Ten XL Protocol, master or slave

Ethernet

Connector

  • RJ-45

Protocol

  • Quartz protocol, SNMP

Electrical

Power

  • Auto ranging 100 – 240V AC, 50/60Hz 40 watts

Fuse

  • 250V, 1A time delay

Physical

Dimensions

  • 19″ W x 1.75″ H x 7.75″ D
  • (483mm W x 45mm H x 196mm D)

Weight

  • 8lbs. (3.5kg)

 

 

Based on 0 reviews

0.0 overall
0
0
0
0
0

Only logged in customers who have purchased this product may leave a review.

There are no reviews yet.

You may also like…

SHOPPING CART

close

Prices May Vary as Per Currency Parity


Please Contact us Before Placing an Order, Thank You.